How to install games on ps3 from hard drive. How to run games on PS3 - a comprehensive solution to the problem

So, you bought a PlayStation 3 and were happy - now you can play interesting games with great graphics. You went to the store to buy these same games and were upset when you saw their cost. You want to buy games cheaper. Or better yet, it's free. It's possible. What you need to do with your PS3 in order to play games downloaded from the Internet will be discussed in the article.

ODE and firmware: what and how

There are 2 ways to cure your PS3 from greed - flash it (jailbreak) or install a drive emulator (ODE). Both options give you almost the same opportunities - record games from the Internet or from a licensed disc onto the internal hard drive, and then play them freely.

The firmware (sometimes called ) additionally allows you to install programs written by enthusiasts specifically for the PS3 (homebrew). These are media players, file managers, custom shells, etc.

“Can I flash my console?”

Unfortunately, this question cannot be answered in the affirmative in all cases. The ability to flash or install ODE depends on the specific model.

PlayStation 3 was released in 3 versions:

This is the first version of the console. For them, both firmware (after downgrade) and ODE installation are possible.

PS3 Slim. Sony began releasing this version in 2009. Set-top boxes released before 2011 and some models released in the first half of 2011 are being flashed. Installation of ODE is possible on all Slim models.

PS3 SuperSlim. The last variant of the PlayStation 3, which appeared in 2012 (after which Sony released the PS4).

Back to freedom, or what is downgrade

When jailbreaking or installing ODE, in addition to the specific model, the version of the official software installed on the console matters. It is possible to install firmware or a drive emulator only on certain versions of official software.

Jailbreaking the PS3 is possible for most FAT models and some Slim revisions if the official firmware version 3.55 or lower is installed on the console.
To install ODE, the official firmware version must be no higher than 4.55

If a later version is installed on the console, then for ODE or jailbreak you need to downgrade.

Downgrade is the replacement of the official firmware with an earlier version, that is, downgrading the firmware version.

What to choose ODE or firmware?

Unfortunately, you have practically no such choice, because the ability to install a drive emulator or flash the console depends on the specific PS3 model. You can only choose between jailbreak and ODE if you have a fairly old console, released in 2006-2010. In all others In cases, installing ODE is the only option.

The easiest way to find out if it is possible to flash and install ODE on your PS3

The possibility of downgrading, flashing, or installing an emulator depends on 3 factors:

1. Specific PS3 model
2. release dates for your console
3. official firmware version.

The easiest way to identify the modification (FAT, Slim, SuperSlim) is that they differ in appearance:

The year of manufacture can be determined by the DATA CODE, which is indicated on the back panel of the set-top box:

DATA CODE consists of a number and a letter. The number is the year of manufacture: 0 is 2010, 1 to 4 correspond to 2011-2014, and 6 to 9 correspond to 2006-2009. The letter is the quarter in which the prefix was released: A - first (January, February, March); B - second (April, May, June); C - third (July, August, September); D - fourth (October, November, December).

In the example in the picture, DATA CODE means that this console was released at the end of 2007.

To view the software version, go to “settings”, select “system settings”, then “system information”:

So, when you have information about the model, release date (DATA CODE), and software version, you can easily find out what can be done with your set-top box: reflash or install ODE. To do this, call 8-800-555-14-13 , provide information about your console, and the consultant will determine which modification: jailbreak or ODE is most optimal for your PS3, and will also suggest the nearest workshop where or.

Instructions

To run the game on the Ps3 game console from an external hard drive, either first format the hard drive (flash drive) in the FAT32 file system. This can be done using Windows OS - to do this, connect the hard drive to the computer and open the “My Computer” window.

Right-click on the disk icon and select “Format”, make sure that there are no files on it that are important to you. Select the FAT32 file system, select the "Full" option and click "Start". In the window that opens, confirm the formatting.

Write the manager.pkg file to your hard drive, you can download this file from the link http://rghost.ru/2865216. Create a separate folder on your disk named Gamez. Next, go to work with the console, check that there are no disks in the drive, disconnect all Usb devices connected to it from the Ps3. Remove the power cable from the console, plug in the dongle, and connect the power cable.

Turn on your PS3, press the button to eject the disc. Use the buttons on the console itself, but not the remote control. If you followed all the steps correctly, it will launch as usual and you will be able to launch the game on Ps3 from the disc. Pull out the dongle after booting and connect the drive ().

Go to the “Games” section in the console, make sure there is an option “install the backup manager”. After that, you can proceed to copying games to your external drive, copy them to the Gamez folder. Insert the game disc into the drive and connect the external media.

Launch the Backup Manager program, as a result you will see the game inserted into the drive and the game on the external drive that is available for emulation. In order to emulate the selected game and launch the game on Ps3, click on the button with a cross. To delete an image, click on the button with the image of zero. Exit the program and you will see the game appear in the menu.

note

Peripherals for PS3. Buy additional accessories for your PlayStation 3 system! This remote is designed specifically for the PlayStation 3 system. It can be used to control playback of Blu-ray Discs and certain other media (such as DVDs and CDs).

Helpful advice

After all, as you know, hacking a PS3 involves reading game images exclusively from the hard drive, so these boxes can only be nailed to the wall as a reminder of your own stupidity. You can, of course, go to an enterprising seller, first armed with brass knuckles, but I think these buffoons have long learned to move to a new place every day.

Sources:

• running games on ps3 without disc

Programs that allow you to delete a hard disk partition and perform other operations with it are called disk managers. There are many such programs known: Partition Logic, BootIt Next Generation, Partition Manager, Acronis Disk Director and others. In the last of the programs listed, the operation of deleting a hard disk partition is reduced to a set of simple sequential steps.

Instructions

Launch Acronis Disk Director.

On the right side of the main program window you will see all hard drives installed on, as well as all existing ones on them. Please note that sections will be shown at the top as separate icons, which cannot be used to judge the number of physically installed ones. At the bottom you will see partitions grouped by the hard drives on which they are located. There can be several partitions on one physical one. You can reduce or increase their size, respectively, increasing or decreasing the volumes of adjacent partitions located on the same hard drive.

At the top of the window, identify the section that you want to delete. Right-click on it and select “Delete” from the pop-up menu. The icon will turn into “Unallocated Space”. If you need further operations, for example, to increase the size of an adjacent disk partition using freed up space, select the appropriate command in the “Wizards” on the left side of the main program window.

After all the operation settings have been completed, click on the black and white flag located in the tool window under the menu bar. You will see a window with a complete list of ongoing operations. Confirm your actions by clicking the “Proceed” button. Once everything is ready, it will display a window with a service message stating that all operations were carried out successfully.

Video on the topic

Downloaded games for the PlayStation 3 game console require you to have special software, as well as any disc in the drive. In addition, please note that the old method of launching downloaded games on a console (jailbreaking) has long been obsolete and is often no longer supported by many developers.

You will need

• - Internet access;
• - removable storage;
• - firmware program.

Instructions

Before downloading games for your PlayStation 3, first check the firmware installed on your device. If you have factory installed software, learn about the procedure for flashing your gaming console so that you can run downloaded games in the future. You can use information from the following site: http://jbreaker.ru/. Before flashing, please read the warranty conditions for the PlayStation 3.

After installing the custom firmware, proceed to launch the downloaded games, having first downloaded them from the Internet (you can find links on special thematic forums, also search for torrents). Download the multiMAN program and the BDEMU drive emulator. Check the downloaded files for viruses and copy them to a removable drive. Insert the flash drive into the console, then go to the “Games” and “Install Package Files” menu.

Using the joystick, first install the multiMAN manager and then BDEMU. Copy the games you downloaded to a removable drive (an external hard drive or flash drive will do). In the multiMAN manager, mark the installation file with a cross, after which the game should mount itself. It is best to first insert any disc into the drive of your console, since not all games launch on their own.

If you used jailbreak before, after flashing, install the Fix Permission program on your console. It is installed in the same way as previous programs, after which you will not see a black screen when starting games. You don't have to install it if there is no such problem, however, save the downloaded installer just in case. Do not forget to check installed equipment and downloaded games for viruses.

Helpful advice

Contact service center specialists for flashing the set-top box if you cannot do it yourself.

Related article

PlayStation 3 is a popular gaming console on which most modern video games are released. Unfortunately, it is not always possible to buy expensive specialized editions, so you need to know how to install the game on PS3.

Instructions

To be able to install games on the PlayStation 3, you must first use special software. Format the flash drive by selecting FAT32 format in the settings. Download the Open Manager and BlackBox FTP programs, unzip them, and copy the resulting files to a prepared flash drive.

Unplug your PS3 (also turn off the switch if there is one), and then put the console into JailBrake mode. Insert the flash drive into the USB connector, and then press the start button. Click on “Eject” (the button designed to eject the disc). Go to the “Install Package” menu and find files there for installing previously downloaded applications. Use the "X" button to install them one by one. Then go to the Game menu and see if the corresponding shortcuts for this software appear. Take out the flash drive.

Install Total Commander (if you don't already have it). Connect your console to your home computer using a patch cord. To install games on your PS3, go to the Settings menu and then select Your Network Settings. Next, find the “Connection Settings” item, select “Special” in the “Setting Method” column. Then in the “Connection method” column, click “Wired”, and in the “Device mode” column - “Detect automatically”. Open the IP settings and check the box next to “Manual”.

Set up connections using the address 192.168.1.2. Then find the “Subnet mask” column and set the value to 255.255.255.0. In the “Primary DNS” and “Default Router” columns, set 192.168.1.1, and do not change the additional DNS. Do not use a proxy server, set the MTU field to “Automatic”, for UPnP use the “Enable” mode. Save the settings using the "X" key.

In the "Game" section, find the BlackBox FTP program. Then open Total Commander on your computer, click “Network”, and then click on “Connect to FTP Server”. To install the game on PS3, click “Add”, write “PlayStation 3” in the “Connection name” field, set the server IP to 192.168.1.2:21, and do not change the password and account fields. Connect to the selected connection.

A menu will appear in front of you in which you need to select the dev_hdd0 directory. Go to the Game menu and then OMAN46756. In this directory, create a folder GAMEZ, and then copy the game you want to install there. Once the copying process is complete, exit the BlackBox FTP program and launch Open Manager. The question will pop up in front of you: “Use OMAN46756.” Click Yes. Select the game you want and press "X". After this, the installation will begin, and after a while you will be able to enjoy the game.

Video on the topic

note

This method is not suitable for Play Station of other models.

Helpful advice

Do not install pirated discs. This method is intended for individual developers who do not release games on discs.

Today we have a large selection of games for every taste and style. Some of them can be purchased already on media, some can be downloaded from the Internet. Store all the information on the hard drive, of course, but there comes a time when space runs out and games need to be transferred to storage media.

Instructions

If the game is free and was downloaded as a file or files, you can easily burn them to a CD or DVD disc. You will need installation files. If you copy an already installed game to disk, there is a chance that it will not launch.

The simplest way is to use standard resources of the Windows operating system. Insert a blank disk into the drive, the OS will turn on the autorun window. Select the option “Burn files to disk”. Then select the media on which you want to record the game: USB or CD/DVD. On the top line, write the disk name. Click "Next".

Sony PlayStation 3 today is one of the most popular consoles in the whole world, with more and more new games being released almost every week. Its main feature is that the device itself is sold to consumers practically at cost. Sony makes money mainly from various add-ons, which also include game discs, the cost of which is quite high compared to others. However, the console itself has a rather nice feature that allows you to save games directly on the console. This is why the question “how to install games on PS3” has become so popular.

How to download and how to run games onPS3?

Many people believe that the answer to the question of how to run games on PS3 is to insert the disc into the drive, however, this is not at all true.

Almost immediately after the release of the new console from Sony, smart users found an excellent way to successfully play their favorite games without overpaying a lot of money to buy disks and install them on the console’s hard drive - this is downloading games from the Internet and sending them to the console using a regular cable. Today, millions of users of the World Wide Web are very successful in exchanging the latest games for Sony PlayStation 3, doing it completely free of charge.

To begin with, you should download an image of the game from the Internet; this is done quite simply, since you can find a lot of specialized sites with similar games.

After this, we connect the set-top box to the computer using a LAN cable or an ordinary Wi-Fi router.

We hand over the game.

It is immediately worth noting the fact that FlashXP must be installed on the computer. Now let's look at both methods.

onPS3 via cable?

First of all, we connect the console to the computer using an RJ 45 cable through a special connector located on the back wall of the system unit.

On PlayStation 3 as follows:

We go to Internet connections, where we select:

Wired connection method.

Special setting method.

Automatic detection of network device mode.

Setting the IP address must be done manually.

Now on the computer, go to the “Start” menu, then “Control Panel”, here we click “Network and Internet”, where we select view the network status. After the transition, a window will open where on the left you can see the item “Change adapter settings”, click on it.

In the window that appears, click on the required adapter and go to its general settings, then click “Properties”, “Internet Protocol Version 4”, and here we again open “Properties”. Then we indicate the unique IP address of the adapter.

We launch a program called Blackb0x FTP Server in the console.

This program should definitely display the IP address that you entered in the console settings.

It’s immediately worth noting the fact that various IP, DNS and other data may be different for users, so it’s worth checking them out initially before launching games on the PS3. Also, many people prefer to play some games from previous versions of this console. Since it is quite possible to run PS2 games on PS3. Many people do this.

If you don’t know the installation method through the program and how to launch games on PS3, then this is done as follows:

In the program menu, click the “Session” button, and then select “Quick connection”.

We press the connect button, after which we see in the right window the complete structure of all console folders. Now in the left window we find the folder with the game we need and move it to the PS3 section. The location of the game should depend on the readings of the installed Backup Manager.

The Sony PlayStation 3 game console itself is an expensive pleasure, and considering that licensed games also cost a lot, knowing how to install a game on the HDD of the console is very useful. Unfortunately, there is no easy and quick way to do this, but if you want, anything is possible. You'll have to tinker a little with programs and settings.

• Blackb0x FTP – for transferring files to the set-top box via FTP;
• Open Manager (or MultiMan Manager, or Backup Manager) – for launching, copying and patching games;
• Total Commander, if it is not already installed on your computer.

• if you installed Open Manager, open the directory “dev_hdd0/game/OMAN46756/” and create a GAMEZ folder there;
• for Backup Manager, the path where games are located is “dev_hdd0/game/LAUN12345/GAMEZ/...”;
• For the “MultiMan Manager” games to work correctly, place them in the “dev_hdd0/GAMES/...” folder.

The copying process can take quite a long time.

By the way, with the help of Open Manager, games that occupy less than 4 GB can be launched from a flash drive, where the game files are located in the same way in the “GAMEZ” folder.

So you came here to get an answer to how to run the PS3 games in this section? You will receive the answer to them below, all point by point, not wanting to read some point is not an excuse to get into the topic and ask questions that already have an answer, or use the search to answer a newbie. There is nothing complicated here, no specific knowledge is required or the like.

What we must have at our disposal to use all the functions
- ps3 with firmware 3.55 and lower, all others pass by for now, fat or slim does not matter
- flash drive or external hard drive formatted in fat32
- demo disc for Ps3 or any disc with the game
That's it, nothing more is required.

Below are spoilers with the necessary points:
Conceptual dictionary (Must read!)
PSjaibreak, PSGroove, Dongle - these are popularly called “flash drives” or “dongles”; they are inserted into a USB console and hack it without flashing it, only for firmware 3.41 and lower. At 3.55 they do downgrade. Nowadays they are not relevant, except for the well-known Cobra USB, which has ample capabilities.

Downgrade- downgrading the firmware cannot be done on the official firmware, only at the Sony service center, so craftsmen are constantly inventing their own methods, two methods are known. 1) using a “dongle” 2) using qa flag (while the instructions are being done, I think there will even be a video in the future.

Update- upgrading the firmware is not a tricky matter, I won’t describe it in detail.

Backup Manager- application for launching games, description below.

Hex-firmware for dongles.

Spoof- this is the firmware number in the “system information”, it only saves you from editing the version in param.sfo and from an accidental update no higher than the spoof version.

Recovery- a special mode that turns on when there is a problem with the PlayStation 3; how to enter it is described in the regular standard instructions for the PS3. It can also be used when changing hdd.

HDD - or hard in slang, means the hard drive of a set-top box or any other (more details google)

Signing keys - in simple terms, this is a very long code that will take 20 years to figure out, but because of it they can’t break the new firmware and sign another toy.

Digital signature - above. (kolob126)

PKG- an installation file like on a PC, like an exe that you install every day, only specifically for ps3.

Debug prefix - I think Google will explain in great detail what it is. A little hint, this is a special version for debugging the software for developers.

Devkit- a special version of the console for game development, different from the standard one, everything else is in Google.
Close
Installing the firmware (Must read!)
We install the official update 3.55 - download the firmware and throw it into PS3/UPDATE/PS3UPDAT.PUP (the name of the file itself) on your flash drive, in the same way you can install any custom or any other update. We go to the settings menu, at the very top there will be an update, select the update from the media and then do not touch the set-top box.

2) We installed the firmware, everything works, we throw any firmware along the same path, the file name should be the same PS3UPDAT.PUP.
3) The firmware is installed, now put any program with the .pkg extension into the root of your flash drive and you will see the installations manager.
Close
Description of firmware
Here I think you choose the firmware to your liking based on the capabilities, an important note, for beginners I recommend Kmeaw and spoof the latest firmware is needed so as not to accidentally update.

Kmeaw- one of the first firmwares, considered the most stable of all firmwares. In this firmware, payload is not built into it like in all the others, but is launched together with the manager for launching games.
I recommend it to all beginners, nothing extra.

Rebug- All firmware from this team was intended as a porting of features from debug firmware and they are there. There is also the ability to install qa flag and there is a dedicated 22gb on hdd for linux. I would like to note the convenient package installation manager.

Waninkoko- outdated firmware, has many bugs associated with the inability to launch games. The good old payload from hermes is integrated into it.

PS3A is based on kmeaw and has a number of differences from it:
- added new lv1 lv2 peek & poke for otheros & others + + new patch
- new icons
- package manager from rebug firmware
- included Bdemu v2 and open ftp via axtux
- added Heavy Rain theme
- spoof 3.66
- added 22 GB system partition for otheros, you just need to install petiboot
- otheros supported (there will be no trophies)
I recommend installing it, everything works the same as on kmeaw, the built-in bd_emu and package installer are very convenient for a beginner.

Description of Backup Manager
There are many Backup Managers - but they all perform one function - launching the game, any manager can handle this, but some of them have a number of additional functions.

Multiman- has the most impressive functionality, it can be recommended to a beginner, but it’s better not to touch incomprehensible options. Can:
- raise ftp
- file manager
- media player in file manager
- various skins and even an xmb clone
- built-in emulator to run nes
And a lot more, generally an irreplaceable thing

Rogero Manager a simple manager with a minimum of settings for launching games, has ftp, edit rights, sfo and of course copy, swap buttons, connect a mouse and keyboard and launch games :).
Close
How to use Backup Manager (run games using it and make images).
Backup Manager This is a program, see how to install it above! If you are reading this further and we have the program installed, then we continue our training. We will need:
-One media formatted in Fat 32 is sufficient to store the game in 10-20 GB.
-One disc with a PS3 game, licensed and no other
-PC and user attentiveness smile

1) You have downloaded the game, you need to unpack the folder from the archive or just copy it, if nothing is packed, the folder will look like this BLES00472, this is the game code, each one has a different number, the number means the game, the set of letters is the region. For convenience, you can rename the folder, say, the name of the game, it will launch.
2) Create a folder on the media called GAMES or GAMEZ.
3) Copy our favorite game
4) Now you just need to go to Backup Manager and select the game you like, there must be a disc in the drive with the game from PS3
5) Now don’t be afraid, we were thrown into Xmb, the name of the image appeared instead of the disk, launch it and enjoy.
(kolob118)

Is there a way to remove a working image via a PC?
There is no such method; everything is removed only through BackupManager's due to technical limitations that no one has circumvented.

Where can I see the compatibility list?
Here is one of the places

Do games run without discs, otherwise I have a console with a non-working laser, I need to somehow adapt it.
It’s possible, but not all games work, mostly old ones before 2010, although there are also new ones, about 30-40 percent, on 3.55 Kmeaw many things won’t run without a disc.
Close
Learning to upload games to the built-in HDD of the console (At the same time mastering PS3 FTP&FileZilla
And so, first of all, we install the x-FileZilla client (or any other) on the computer, do not configure anything in it for now, now we install the ps3ftp or multiman program itself, in the same way we throw it into the root of the flash drive and install it as a backup manager. Now the setup:
1) On the PC for the network connection, enter the following parameters:
ip address: 100.100.10.1
Subnet mask: 255.255.255.0
That's it, we don't touch the rest.

and in pictures for the completely helpless
pic
pic
pic
2) On ps 3 we set up a network connection to the Internet
We set everything automatically, except for setting the IP address, enter the following data:
ip address: 100.100.10.10
Subnet mask: 255.255.255.0
Default Gateway: 100.100.10.1
Primary DNS address: 100.100.10.1
3) Launch the program and click start ftp (in multiman we do not click anything)
4) In the client we write the IP of the set-top box, it will also be displayed on the screen 100.100.10.10, the name is FTPD12345 and the password is gremlin (kolob107), and port 21.
5) We have all connected to the console, now we are looking for the path dev_hdd0/game/LAUN12345/GAMEZ (or dev_hdd0/GAMES/ for new managers), copy all the games there
If the program loses the connection, simply exit it and enter again.

Downgrade from 3.55 and below.
Downgrade method using dongle:
To roll back from 3.55, we will need to roll back to patched 3.41, which will think that it is 3.56 (that is, it will not allow you to install even 3.55), and with patched 3.41 you can roll back to any firmware (that is, if your ps3 was released with firmware 3.40 , then you will not be able to roll back below it, but only to 3.40.
Before rolling back, you must install the appropriate firmware for rollback on your PSJailbreak + bricks from custom firmware 3.55 are treated with this rollback.
Rollback from 3.55
1) Completely turn off the PS3 Fat (power switch).

2) Place the files for downgrade into the root of the flash drive with the FAT32 file system:
- Lv2diag.self (from the File1 folder)
- Modified firmware 3.41 (Don't forget to unzip)

3) Insert the stitched jailbreak for downgrade into the set-top box into the rightmost USB port (closest to the BD Drive).

4) Turn on the set-top box (supply power, power button and immediately the “Eject” button). The console will turn itself off without anything appearing on the screen. You can start the set-top box without devices in the USB port to make sure that the transition to Service mode has been completed - there will be a red rectangle on the right. Turn off the PS3 using the controller (if you turned it on).

5) Remove Jailbreak. And insert the USB flash drive into the same port with the files previously copied to it.

6) Turn on the PS3. The downgrade will begin, nothing will be displayed on the screen, the flash drive will sometimes blink. Wait (about 5 minutes) until the set-top box turns itself off.

7) Take out the flash drive, delete the files from it that you copied earlier and copy the Lv2diag.self file from the File2 folder to the root (To exit the service mode).

Rollback from 3.41 to any firmware:
1) Connect the dongle to the right port of the console (the console must be turned off), disconnect the power cord, wait a couple of seconds and return the cord to its place. Press the Power button and immediately press Eject. The screen will blink for a while and then turn off. You can remove the dongle - the console has entered Factory Mode.
2) Take a flash drive formatted in FAT32. Upload 2 files - Lv2diag.self and PS3UPDAT.PUP to the root of the flash drive. The file "Lv2diag.self" is taken from "Lv2diag.self FILE 1".
3) Insert the USB flash drive into the right port of the console and turn off any other USB devices. Press the Power button. We wait until the console turns off again. If the console does not turn off by itself, then turn it off yourself through the XMB menu.
4) Take out the flash drive and format it to FAT32. Upload "Lv2diag.self" from the folder "Lv2diag.self FILE 2" to the root. We plug the flash drive into the right port and press Power. The console will exit Factory Mode.
Any firmware will do. In distribution 3.15.

Launch PS1, PS2, PSP Minis and other content from psn.
Changing HDD on ps3
How to download and install patches for games?
QA Flag, as well as what it is and how to install it.
FAQ:
Do you need to insert jailbreak into usb to install custom firmware and play games?
No, now it is not required at all, just install the update, the set-top box will accept it as native.

Is it possible to just record the game on a disc and play from it?
This option is not possible, at least for now.

Help! I installed a backup manager, but it won’t launch games, what should I do?
You probably have firmware 3.55 and multiman manager, install the file from the bd_emu distribution.

Can I image my ps3 drive?
Sure you can.

Do all games work through the eboot patch?
Unfortunately, not everything, since you need to understand how the eboot completely works, so after sitting in the hex and understanding it, you can theoretically make everything work. In the meantime, the patches contain the games that are easiest to remake.

I want to play psn again and install the latest update, will they ban me and how can I do this?
You won’t be banned, just connect your set-top box to the Internet and do an auto-update, you don’t need to do any extra steps anymore.

If I set it to 3.55, can I roll back to 3.41?
Of course you can, the easiest way is qa flag)

Will PSN work on custom firmware?
Of course, but you most likely won’t be able to play with a patched eboot, since the game may require a patch, and it’s very difficult to remake an eboot from a patch.

When installing the program, I get error 80029564, what should I do?
Apparently the program is not signed, download the signed version.

When will the latest firmware be hacked so you can play games?
Wait, as soon as they hack, you will find out from this topic and other sites.
--------------------
Relevance of firmware and other things
At the time of writing these lines, this information is current:
The latest official firmware for ps3 is 3.70
The latest hackable firmware for Ps3 is 3.55
The latest firmware can be downgraded - 3.70 (only using the progskeet chip)
psn availability on hacked consoles - no